Structural stress
Contents |
[edit] Introduction
A material under stress is in a state that has resulted from the application of a force or forces. These forces can also be called stresses. The effect on the material will depend on the type of stress that is applied.
Stress patterns in structural elements can be complex but they usually comprise just three basic types of stress:
- Tensile.
- Compressive.
- Shear.
[edit] Tensile stress
If the stress acting on a structural member tends to make it longer, it is said to be under tensile stress or 'in tension'. The load carried by each unit area of the member’s cross section is the tensile stress in the member. This will make the member a ‘tie’. Steel is ideally suited to resist tensile stresses and is used widely in construction for this purpose, for example to reinforce concrete, or in the form of cables, wires and chains.
For more information see: Tension.
[edit] Compressive stress
If the stress acting on a member tends to result in it shortening (its components are pushed together), it is said to be under compressive stress or 'in compression'. The load per unit area of the member is the compressive stress. This makes that member a strut, or if the member is large, it might be a column, pier or stanchion, depending on its position in a structure. Most materials can carry some compressive stresses – other than cables, wires, chains and membranes.
For more information see: Compression.
[edit] Shear stress
Shear stresses make the particles of a material slide relative to each other and usually result in deformation. An example is a riveted connection which can shear when excessive force is applied. Vertical forces acting on a cantilever can make it shear off at the wall junction. Shear forces produce shape deformation in materials eg, a rectangular element can be contorted into a skewed parallelogram. The shear stresses are those acting on the planes along which the sliding takes place and are measured across a unit area.
For more information see: Shear.
[edit] Units of stress
The N/m2 is the basic SI unit of stress but is very small for most purposes. As a result, MN/m2 may be used, often expressed as N/mm2 in structural codes for steel, concrete and timber.
[edit] Related articles on Designing Buildings
- Bending moment.
- Compression.
- Concept structural design of buildings.
- Bearing capacity.
- Failure of cast iron beams.
- Lateral loads.
- Limit state design.
- Moment.
- Point of contraflexure.
- Racking.
- Rebar.
- Shear.
- Shell roof.
- Structural principles.
- Structural steelwork.
- Strut.
- Tensile strength.
- Tensile structures.
- Tension.
- Ties.
- Types of structural load.
Featured articles and news
Getting the most out of heat pumps and heating
How heat pumps work and how they work best.
Plumbing and heating for successful retrofit and renovation
Low temperature underfloor systems and heat pumps.
Cost-of-living crisis and home improvement plans
Starting on the right footing and top tips for projects.
Delays on construction projects
Types, mitigation and the acceleration of works.
From Chaucer to Fawlty Towers.
Electrotechnical excellence, now open for entries.
Net zero electricity grids BSRIA guide NZG 5/2024
Outlining the changes needed to transition to net zero.
CIOB Global Student Challenge 2024
Universitas Indonesia wins for second year running.
New project and cultural district described in detail.
The nature of EPCs, crticism and inaccuracies.
History, issues and redesign.
From waste recycling to energy performance the hierchy.
An introduction to WERCS and WEEE responsibilities
Dealing with 2 million tonnes of waste equipment a year.
Global BACS Market: analytics and optimisation
A BSRIA glance at building automation and control systems.
What it is and how to use it.
Types of insulating plaster by binder and insulant.
Investors in People: CIOB achieves gold
Reflecting a commitment to employees and members.
Scratching beneath the surface; a guide to selection.
ECA 2024 Apprentice of the Year Award
Entries open for submission until May 31.
UK gov apprenticeship funding from April 2024
Brief summary the policy paper updated in March.